布线发展史

Picture Perfect AV Systems

Whether it’s video conferencing or digital signage, many of you are likely facing requests from your customers to deploy cable plants that support audio-visual systems.

2018 年 5 月 9 日

升级到四线对 PoE:您需要知道的内容

多年来,您一直在部署支持以太网供电 (PoE) 的线缆设备,以用于 VoIP 电话和监控摄像机等各种设备。So far, up to 30 Watts is all you’ve been requested to support, but with the plethora of devices now able to take advantage of higher levels of PoE—like the latest 802.11ac Wi-Fi access points, digital displays and even desktop computers—your customers are starting to ask for four-pair PoE.

2018 年 5 月 2 日

Why can’t I use the 2-cord test method?

Like the TIA and ISO, Fluke Networks promotes the use of the 1-cord method to set reference for fiber loss measurements. The 1-cord method is where a launch cord is attached to a light source and the other end to a power meter. A reference is then set (the power measured is defined as 0 dB). Next, the launch cord is disconnected from the power meter, but not the light source. Then the far end of the launch cord is attached to the cabling under test and a receive cord between the far end of the cabling under test and the power meter.

2018 年 4 月 25 日

电缆测试 101:But the Standard Says 0.75 dB!

We’ve covered fiber insertion loss testing in depth in many blogs, so by now you should know that it is the loss of signal that happens in a channel due to the length of the cable and any connectors, splices or splitters.

And hopefully you also know that estimating your loss budget involves adding up the loss of all of these components to make sure you’re within the loss limits specified by IEEE standards for the application you plan to run.

2018 年 4 月 18 日

Let’s All Calibrate and Have a Good Time!

Just like those who drive around long after the engine service indicator lights up on the dashboard, there are folks out there who have likely been putting off getting their t

Calibrate Testing by Network Technicians

ester calibrated despite the email or LinkWare Live notification from Fluke Networks.

2018 年 4 月 4 日

Too Soon to Say Goodbye? It’s All Relative…

You might remember that just about three years ago, the DTX CableAnalyzer™ was officially retired. Since its discontinuation, Fluke Networks has continued to offer technical support, repair and calibration for this tester that was once touted as the ultimate time saver and brought testing to a whole new level when it was introduced in 2004.

2018 年 3 月 28 日

101 系列:LEDs vs. VCSELs

Since today’s high-speed fiber networks use 850-nm vertical-cavity surface-emitting laser (VCSELs) transceivers, some may be confused about why light emitting diode (LED) light sources are used for testing. Understanding the differences between these two sources will certainly shed some light.

2018 年 3 月 21 日

101 系列:What is Modal Bandwidth?

Often when we hear the term “bandwidth” we think of how much data can be sent over a fiber link. But when we look at fiber specifications, we typically see a specification for modal bandwidth, or effective modal bandwidth (EMB). This key characteristic of multimode fiber refers to how much data a specific fiber can transmit at a given wavelength, and it is dependent on another characteristic—differential mode delay.

2018 年 3 月 7 日

OTDR:您的终极故障排除工具

So you’ve finished your fiber cable installation and are now on to the task of certifying the cable plant using an optical loss test set (OLTS) – it’s the tool you need for Tier 1 certification and theTesting with OptiFiber Pro OTDR most accurate for measuring loss to ensure application support.

2018 年 2 月 28 日

您的光纤末端是否是正对正对着?

While it seems we can never hammer home enough the need to properly clean and inspect fiber end-faces since contamination remains the number one cause of fiber link failures, have you ever thought about what exactly you are cleaning and inspecting?

2018 年 2 月 21 日